Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

User

Don Casillas

Joined on the:

Aug. 11, 2009

Score

1480

Comment(s)

7

Voted question(s)

1

Voted answer(s)

0

Votes up

0

Votes down

1

Votes up received

3

Votes down received

0

Recent Activity

Question(s) asked

8

Answered question(s)

5

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question
RECENT ACTIVITY QUESTION(S) ASKED ANSWERED QUESTION(S) COMMENTED QUESTION(S)

17/01/2024

 Dodge Don Casillas (1480Pts.)

0

Late 2023 Durango Headlight Switch Connector FYI

The later Durango (mine is 8/2023) has a different headlight switch connector than earlier models as shown in install guide. It does have a white/brown wire that does change with switch position. Will the Evo-All have any problems with this connector change?
Login to reply View 1 answer(s)

07/03/2020

 Ford Don Casillas (1480Pts.)

0

Anything available for 2020 Ford Explorer or Police Interceptor yet?

Checking to see if there are any big differences for the 2020 Ford Explorer wiring, it is not listed yet. Or if T-harness available. We have some coming in soon, basic civilian/personal versions and police interceptor fleet versions. Thanks!
Login to reply View 0 answer(s)

17/01/2020

 Chevrolet Don Casillas (1480Pts.)

0

EVO-ALL with RF Kit-No heated seats in 2015 Chevy Traverse

EVO-ALL with RFK942, stand-alone install. Heated seats do not turn on when remote started with RF kit or 3x lock, they do work with factory remote start. All tested well below temp. Install manual #59201 lists heated seats as an option. Option is turned on in programming. Are other options or wiring needed to get the heated seats to work?
Login to reply View 1 answer(s)

20/08/2019

 Land Rover Don Casillas (1480Pts.)

0

Any solutions yet for Range Rover 2012 + up?

Any solutions yet for Range Rover 2012 + up?  Anything?

Thanks!  
Login to reply View 1 answer(s)

15/06/2016

 Ford Don Casillas (1480Pts.)

0

2016 Explorer Police Interceptor

Has anyone done one of these yet? Have 3 coming in, standard keys (no transponder at all) and no factory remotes? Will I even need an EVO-ALL or hardwire aftermarket remote start?
Login to reply View 1 answer(s)

05/01/2014

 Nissan Don Casillas (1480Pts.)

1

Evo-Ride Not Programming In 2003 Nissan Altima

Previous same question never posted to site? Evo-Ride hardware v3 firmware 2.03, hardwired into 2003 Altima with 8 pin immobilizer connector, will not program. Remote starter works fine with key in ignition. All programming steps and LED blinks are good until key is turned on. Red LED goes solid red every time. All immobilizer wiring checked, metered, and confirmed correct in factory service manual. While troubleshooting, I found that pressing the programming button 5x (instead of 4x) then turning the key on, the red LED will blink 10x like it was programmed correctly. But the car will not remote start and the red LED stays on solid even after remote starter shuts down. Repeated programming process, same results. Tried another new Evo-Ride, exact same problem. Can the Evo-Ride be reset or firmware upgraded if needed? Any help will be appreciated. Thanks!
Login to reply View 1 answer(s)

14/12/2013

 Chevrolet Don Casillas (1480Pts.)

1

Ground while running not needed with Evo-All and THAR-GMv2...?

2013 Chevy Cruze with flip key. Just curious how/why the (-) ground while running input is not needed in data-link installation with remote start, but is needed in many other installs where data-link is used. Just an inquiring installer mind.
Login to reply View 1 answer(s)

27/11/2013

 Toyota Don Casillas (1480Pts.)

1

Evo-All Not Programming in 2013 Toyota Highlander PTS (not Hybrid)

Using EVo-All (hardware 6, FW 4.18 and is correct per install manual) with Ultrastart remote starter via datalink for 2013 Toyota Highlander push-to-start. Programming is fine up to step #5. While blue LED is blinking, when the programming button is pushed 1 time, the LED's never change to blue AND yellow blinking. Only blue continues to blink. Rechecked wiring and confimed proper CAN-H and CAN-L connections. Have not tried to reverse them as wiring is correct. What can be wrong or what needs to be tested?
Login to reply View 1 answer(s)

No results

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question

TECHNICAL SUPPORT

Search through our most popular products and installation topics available in our Question & Answers section.

Learn more
Download our step-by-step troubleshooting guides app available for both iOS and Android or browse through our desktop version.

Learn more
Access the industry’s largest online wiring diagrams & photo database. A free token is provided in every EVO-SERIES box.

Learn more
You did not find the information that you were lookingfor? Ask us a question by filling out the technical support form request. A product specialist will answer you shortly.

Learn more
From state-of-the-art vehicle remote control and connectivity solutions to premium technical support, learn why you should choose Fortin products.

Learn more

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue